Discontinued
Model: np-v302h
Replaced By NP-ME382U
$799.00 USD
The NEC V302H with a native 1080p resolution is designed to provide higher brightness for classrooms, meeting and conference rooms that have heavy ambient light but require a small projector. This 3000-lumen lightweight mobile model is 3D Ready and includes a 8W speaker, closed captioning and horizontal & vertical keystone correction. Enhanced connectivity, including dual HDMI (HDMI 1 supports MHL) , computer, composite inputs and RJ45, are clearly color-coded and labeled on the panel.
  • Native 1080p resolution for connection to full high definition sources
  • Horizontal & Vertical Keystone adjustment to fit the screen properly when used in portable applications
  • ECO Mode™ technology helps extend lamp life and lowers power consumption
  • Dual HDMI input connects you to high-definition sources
  • HDMI 1 supports MHL for connection to smart phones
  • Crestron RoomView Connected™ provides unified management, including the ability to switch the power on and off for multiple projectors connected to a network



Legal Disclaimer To California Residents
WARNING: This product can expose you to chemicals including Styrene and Formaldehyde (gas), which are known to the State of California to cause cancer, and Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov


Display

Aspect Ratio 16x9 Native Resolution 1080p 1920x1080
Maximum Resolution 1080p 1920 x 1080 Contrast Ratio (typical) 8000:1 with Dynamic Contrast

Synchronization Range

Horizontal (Analog/Digital) 15-100 kHz Vertical 50-120 Hz

Signal Compatibility/Connectivity

Supported Video Standards NTSC, NTSC4.43, PAL, PAL-60, PAL-M, PAL-N, SECAM SD/HD Video Signal Compatibility 480i, 480p, 576i, 576p, 720p, 1080i, 1080p
PC Signal Compatibility VGA, SVGA, XGA, SXGA, SXGA+, UXGA, 1080p Macintosh Signal Compatibility Yes
Sync Compatibility Separate Sync / Composite Sync / Sync on G External Control RS-232, IR, DDC/CI,RJ-45
Input Terminals
RGB1(analog):
VGA 15-pin D-sub, Component video using ADP-CV 1E
RGB2(digital):
HDMI(MHL) w/HDCP
RGB3(digital):
HDMI w/HDCP
Video 1:
RCA
Audio 1:
1/8 in. stereo
Audio 2:
L/R RCA (shared by video sources)
Output Terminals
Audio Out:
Yes (variable)
Monitor Out:
VGA 15-pin D-sub

Power Consumption (typical)

On 280W / 217W / 3.0W / 0.5W Input Current 2.8A
Power Requirements 100-240V AC, 50/60 Hz AC, 50/60 Hz  

Physical Specifications

Dimensions (WxHxD)
Product:
12.6 x 9.8 x 4.0 in. / 324 x 250 x 101mm
Weight
Net Weight:
6.4 lbs. / 2.9 kg

Environmental Conditions

Operating Temperature 41-104°F / 5-40°C Storage -14-122°F / -10-50°C

Limited Warranty (parts & labor)

Registered owners receive a 3 year parts and labor warranty including InstaCare next business day exchange. One year on lamp.  

Additional Features

  • Filter Free Design
  • Horizontal & Veritcal Keystone
  • 3D Ready, PC frame sequential at 120Hz
  • Direct power on/off
  • ECO Mode technology
  • Closed captioning
  • Virtual Remote
  • Sleep timer
  • Quick power-off
  • Built-in wall color correction
  • Advanced AccuBlend
  • AutoSense
 

Optical

Display Technology DLP (0.65" DMD) Light Output(Lumens) 3000 normal
Lamp Type 218W AC Light Source Life 3500 hours normal / 6000 hours eco
Screen Size (diagonal) 40 to 300 in. / 1.02 to 7.62m Throw Ratio 1.5-1.8:1
Projection Distance 4.9 to 32.8 ft. / 1.5 to 10.0m Projector Angle 11.7° tele / 14.0° wide
Lens
Zoom:
1 to 1.2
Focus:
Manual
F number, fnumber:
F=2.55 - 2.85, f=22.41 to 28.82mm
Keystone Correction /- 30° horizontal, +/- 30° vertical

Mechanical

Installation Orientation Floor/Front, Floor/Rear, Ceiling/Front, Ceiling/Rear Fan Noise 35 dB normal / 32 dB eco
Regulations "USA: UL60950-1 (2) / UL, FCC Part15 Class A / FCC DoC, Canada CSA C22.2 60950-1-07 (2) / C-UL, ICES-003 Class A / DoC of Canada"  

Virtual Remote
Used over the VGA cable to control the projector directly from a computer without the need for additional control cables.
Crestron Roomview
Provides unified management, including the ability to switch the power on and off for multiple projectors connected to a network.
AutoSense™
Intuitively syncs the projector with most computer signals and features one-touch image optimization.
Powerful 8W stereo speakers
Provide the volume needed for small to medium-sized rooms
Carbon Savings Meter
Calculates the positive effects of operating the projector in ECO Mode, which is encouraged by an optional message at startup. A green ECO Mode button on the remote control makes the switch easy.
Dual HDMI inputs (with HDCP)
Ensure quick switching between presentations and allows for simultaneous digital connections of high-definition sources, such as Blu-ray players, cable boxes, satellite receivers and computers
1080p native resolution (1920x1080)
High resolution provides detailed display of text, graphics and images. HD video is displayed in 16:9 wide aspect ratio.
BrilliantColor™
Advanced video processing from Texas Instruments delivers exceptional picture management control for both progressive and interlaced sources, while making images more vibrant, colors more realistic and blacks richer with detail.
DLP Technology
High contrast images (10,000:1) from the latest Texas Instruments DLP engine featuring BrilliantColor™ technology with improved color accuracy
ECO Mode™
Extends lamp life, lowers audible noise and reduces total cost of ownership.
Built-in Wall Color Correction
Presets provide for adaptive color tone correction to display properly on non-white surfaces.

Reviews

Projector Central - NEC NP-V302H Review: 1080p DLP Projector for Business and Education
Labs Editor Bill Livosi praises NEC Display’s V302H 1080p projector for a multitude of benefits, including its picture quality and attention to design detail in this product review.

Press

NEC DISPLAY ADDS 3,000-LUMEN PORTABLE HD DIGITAL PROJECTOR TO V SERIES LINEUP
Keystone Correction, Broad Connectivity Options Complement New Chassis in V302H Projector

Warranty Length: Registered owners receive a 3 year parts and labor warranty including InstaCare next business day exchange. One year on lamp.

Select where this product will primarily be used to see available warranties:

We're sorry, but this product does not offer service plans for personal residences.

Extended Warranty - Limited parts and labor warranty, including InstaCare
Extended Warranty - Limited parts and labor warranty, including InstaCare

Cables/Adapters

Marble DCS1 USB-C Dock
  • 2-in-1 USB-C docking & charging station that expands USB-C to HDMI, USB-A 3.0, microSD & charge up to 4 devices simultaneously
  • Built-in 65w AC adapter. Supports input voltage range 100-240V, 1.4 A, 50/60 Hz. Compatible with 12-inch MacBook, 13 in New MacBook Pro Standard and TouchBar). NOT compatible with 15 inch New MacBook Pro charging, but can still be used as hub and dock
  • HDMI Type-A supports monitor resolution: 1080p/60Hz, 1920x1200/60Hz, 2560 x 1440/60Hz or 3840x2160(UHD )/30Hz
  • USB-C 3.0 & USB-A 3.0 Ports. Max. power output 12W. Supports 5W/2.4A, 5V/2.1A and 5V/1A charging. MicroSD reader: max data transfer speed: 400 Mb-500Mb/s.
Power Cable
RGB Signal Cable
Refurbished
RGB Signal Cable

Large Screen Display Misc

MultiPresenter Stick
  • Simple device PIN# access for secure connectivity
  • Screen mirroring for Android and Windows devices
  • Includes a simple annotation software allowing for user collaboration
  • Run apps and share files easily

Mounts/Mounts Accessories

Ceiling Mount
Refurbished
Ceiling Mount
Adjustable Extension Column, 2' - 3'
Adjustable Extension Column, 3' - 5'
Refurbished
Adjustable Extension Column, 2' - 3'
Refurbished
Adjustable Extension Column, 3' - 5'
Ceiling Plate
Refurbished
Ceiling Plate
Adjustable Extension Column, 12" - 18"

Replacement Remotes

Remote Control

Lamps

Replacement Lamp

Cases

Carrying Case

  • Remote control
  • Batteries
  • User manual on CD-ROM
  • Quick Start Guide
  • Product registration card

Have a problem with your NEC Monitor? Here you'll find common questions. If you do not find a sufficient answer, please do not hesitate to contact us at 800-632-4662.

Projectors

  • In the projectors on screen menu select the Setup option.
  • Under setup go to Installation or Installation 1 in the sub menu.
  • Within installation you will need to select Orientation.
  • In orientation select the box that says desktop front, press enter and change the option to either ceiling front or ceiling rear depending on which direction the unit is facing in regards to the screen.
This tip works for most NEC Projectors: First, ensure that the projector is powered “on.” Second, hold down the “cancel” or “exit” button on the projector for about 15 to 20 seconds.
  • If the lamp indicator light on the projector is solid red then you would need to change the lamp as it has been used beyond its usable life.
  • Once the new lamp is installed you will need to reset the lamp hours of the projector with the remote control.
  • While the unit is in standby mode, meaning the power light is solid orange, you will need to hold down the help button on the remote for 10 to 15 seconds.
  • Once the lamp hours are reset the lamp LED light will go out and at that time the unit should power on normally.
You will need an additional accessory called a remote mouse receiver -Part Number NP01MR. 3 Ways to Order:
NEC projector input panels feature RGB computer inputs, a composite video input (yellow RCA type plug) and an S-Video input. The RGB computer input (blue) and can also be used with an optional component video adapter for connection to a DVD player or other video source, if desired.
Function F* (this varies from computer to computer)
This can be done by going into the OSM and making the change there or by sending a specific RS232 command to the projector from a computer.
If you are experiencing an issues related to image quality, colors, and signal, Factory Reset is the first setup to perform. (Please make a note of any custom setting prior to doing a factory reset.)
With certain NEC projectors it is possible to project onto non-flat surfaces such as cylinders or corners using free software such as the Geometric Correction Tool, Keep in mind that the 16:9 format will not be supported.

To permanently save your digital keystone corrections by activating "3D Reform Memory." To do this:

1. Go to the "Extended Menu" and choose "Projector Options."
2. Choose "Setup" and go to page 4.
3. Choose the checkbox "3D Reform Memory" and press OK.

Your horizontal, vertical and diagonal 3D reform (keystone) data will now be permanently saved.

The flash memory card or USB drive must be formatted with the FAT16 or FAT file system. (FAT32 and NTFS are not recognized.)
The PC card slot, which is situated on the projector main unit, allows you to make presentations without a PC. Just insert a compact flash or flash memory card containing your stored presentation material and display images directly onto a screen. The projector will display JPEG, BMP, TXT and text-only HTML files.

To present your digital images or stills using an NEC projector you can use the following memory cards:

Compact flash cards (with a Type II PCMCIA CF adapter)
Smart media (with a 4-in-1 Type II adapter)
Memory stick (with a 4-in-1 Type II adapter)
Memory stick pro (with a 4-in-1 Type II adapter)
Multimedia card (with a 4-in-1 Type II adapter)
Secure digital (with a 4-in-1 Type II adapter)

The PC Card Viewer and the Blackboard Function. Projectors equipped with the PC Card Viewer feature are particularly suitable for mobile use since you do not need a notebook or PC to make a presentation. Instead, you can take your presentation along with you stored on a normal PC card or Compact Flash card. Meanwhile, the Blackboard feature allows you to create drawings via the USB mouse and project them onto a screen, facilitating interactive presentations and audience rapport.
Yes. NEC projectors are fitted with inputs for video and S-Video, and meet NTSC, PAL, SECAM, 4.43NTSC and PAL60 standards. You can connect the projector using video, S-video and component (YUV) cables. Please, all projectors are PAL Progressive-enabled (via YUV or RGB). The latest NEC projectors produce virtually no irritating fan noise.
Most projectors use LCD technology. This splits light into the primary colors red, green and blue. Each color is then directed through an LCD display acting as a ‘light valve’ and the light is then reassembled. There is an LCD display for each individual pixel and each primary color. DLP technology involves the use of huge numbers of tiny quadratic mirrors arrayed on a Texas Instruments DMD chip. Only when a mirror is tilted will it reflect the light shining onto it back towards the screen. This very high-frequency switching on and off of points of light is not perceived by the human eye and allows different shades of color to be portrayed. The colors are generated by a color ribbon featuring the primary colors red, green and blue.
It depends on the installation environment. In environments with more ambient light, we recommend choosing DLP. For the greatest flexibility, choose an NEC projector that features both technologies.
Check your projector's installation guide, or use our Image Calculator.

Keep in mind that distances shown in the Installation Guide or Image Calculator may vary ± 5%. We recommend that you verify the distance before the projector is installed.
As a general rule, the distance between the viewers and the screen should between 1.5 and 6 times the image width.
Your ideal screen will depend on your installation, the size of the room, the amount of ambient light, and other factors. We recommend contacting your installer or a screen vendor for screen recommendations.
Most lamps have an expected life of about 2000 hours.

There are several things you can do to increase your lamp life.

• Always make sure there is adequate clearance near the intake and exhaust vents.
• Keep the environment clean and relatively dust free.
• Clean air filters every 100 hours, or more often if there are a lot of dust or contaminants in the room.
• Striking the lamp ages the lamp as it causes slight changes to the shape of the electrodes that light the lamp, so light up your projector when you're ready to use it and avoid frequent on and off cycles.
• Avoid shock to the lamp or projector. • Use Eco-Mode, if your projector has it. • After you run the projector, leave it plugged in until the fan turns itself off. • Avoid storing the lamp or projector in extreme temperatures or humidity levels.

Certain projector lamps contain mercury. Some states have laws that require projector lamps to be disposed of as a hazardous material if they contain mercury. Check with your audio-visual sales associate or local municipality to find out what the projector lamp disposal laws are for your state. You may also contact NEC Technical Support to have your lamp recycled by NEC Display Solutions.

For Windows XP (ver. 2.08):

LT265 & LT245 (Firmware Version: 1.04 or later) / WT610 (Firmware Version: 1.08 or later) / LT380 / LT280 / NP3150 / NP2150 / NP1150 / NP3151W / NP905 / NP901W / NP2000 / NP1000 / VT800

For Windows Vista (ver. 2.08):

LT265 / 245 (Firmware Version: 1.04 or later) / WT615 / 610 (Firmware Version: 1.08 or later) / LT380 / 280 / NP3150 / NP2150 / NP1150 / NP3151W / NP905 / NP901W / NP2000 / NP1000 / VT800

For Mac OS (Intel) (ver. 1.2.5)

LT265 / LT245 (Firmware version: 1.03 or later) / LT380 / LT280 / NP3150 / NP2150 / NP1150 / NP3151W / NP905 / NP901W NP2000 / NP1000 / VT800* / WT610 (Firmware version: 1.00 or later)

For Mac OS (PowerPC) (ver. 1.2.4)

LT265 / LT245 (Firmware version: 1.03 or later) / LT380 / LT280 / NP3150 / NP2150 / NP1150 / NP3151W / NP905 / NP901W / NP2000 / NP1000 / VT800* / WT610 (Firmware version: 1.00 or later)

*The "Easy Connection" function cannot be used with VT800.

Virtual Remote Tool is compatible with NP300/400/500/500W/600 models.
PC Control is designed to control a single projector, while PC Control Pro is designed to control multiple projectors.
The PC Control Utility or PC Control Pro can be connected from your computer to the projector using a serial or LAN connection.
Select "Lamp Mode" on the remote control and use the menu to select Eco-Mode.
Excessive moisture, dust, heat and smoke.
You're seeing the result of dust build-up on the green LCD panel. We recommend that you schedule a service visit. Please contact NEC technical support or your local NEC service provider to set it up.
No, NEC only provides service support and parts to NEC authorized servicers and technicians. NEC-authorized service centers/technicians have attended training classes to ensure quality service on NEC products
Contact Sales Contact Support