Discontinued
Model: np-um330wi-wk1
Replaced By NP-UM330Wi-WK
Call for pricing: 866.771.0266
The UM330Wi-WK1 interactive projector brings collaboration to both classrooms and conference rooms alike. Together with a PC or Mac, the teaching tool will increase students' attention and interaction within the classroom, increasing their retention of subject matter. This bundle includes the 3300-lumen UM330W widescreen ultra short throw projector, NP02Wi interactive eBeam module and stylus pen, and NP04WK1 wall mount kit. The UM330Wi-WK1 delivers an extremely short throw distance, and the interactive eBeam module attaches directly to the front of the projector and uses IR to determine the pen's position within the image for accurate control and annotation. The UM330X is able to mount on the wall directly above the screen using the NP04WK1. Features of the projector include a powerful 16W speaker, closed captioning, RJ-45, wireless LAN (optional), dual HDMI, VGA and a microphone input to amplify the presenter's voice.
  • eBeam interactive system and software converts a standard whiteboard into a complete interactive surface for annotation and collaboration locally or via web meetings
  • Ultra short throw lens (0.36:1 throw ratio) eliminates shadows on the screen along with projected light in the presenter’s eyes created by traditional front projection systems
  • Comprehensive input/output panel, including dual HDMI, VGA and a microphone input
  • ECO Mode™ technology helps extend lamp life and lowers power consumption
  • Virtual Remote allows a presenter to control the projector from the computer desktop without using the physical remote control
  • Remote monitoring and control of projector over network saves IT employee time and reduces costs related to projector operation



Legal Disclaimer To California Residents
WARNING: This product can expose you to chemicals including Styrene and Formaldehyde (gas), which are known to the State of California to cause cancer, and Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov


Display

Native Resolution WXGA 1280x800 Maximum Resolution UXGA 1600 x 1200
Contrast Ratio (typical) 3000:1  

Synchronization Range

Horizontal (Analog/Digital) 15-100 kHz Vertical 50-120 H

Signal Compatibility/Connectivity

Supported Video Standards NTSC, NTSC4.43, PAL, PAL-M, PAL-N, PAL 60, SECAM SD/HD Video Signal Compatibility 480i, 480p, 576i, 576p, 720p, 1080i, 1080p
PC Signal Compatibility VGA, SVGA, XGA, WXGA, WXGA+, SXGA, SXGA+, UXGA Macintosh Signal Compatibility Yes
Sync Compatibility Separate Sync / Composite Sync / Sync on G External Control RS-232, IR, Wired LAN, DDC/CI, USB, Wireless LAN (optional)
Input Terminals
RGB1(analog):
VGA 15-pin D-sub, Component video using ADP-CV 1E
RGB3(digital):
HDMI
Video 1:
RCA
Video 2:
S-Video
Audio 1:
1/8 in. stereo
Output Terminals
Audio Out:
Yes (variable)
Monitor Out:
VGA 15-pin D-sub

Power Consumption (typical)

On 344W / 233W / 8W / 0.2W Input Current 4.0A/2.0A
Power Requirements 100-240V AC, 50/60 Hz  

Physical Specifications

Dimensions (WxHxD)
Product:
26 x 22 x 20 in. / 660 x 559 x 508mm
Weight
Net Weight:
49 lbs. / 22.2 kg

Environmental Conditions

Operating Temperature 41-104°F / 5-40°C Storage -4-122°F / -20-50°C

Limited Warranty (parts & labor)

2 years.  Lamp warranty is 1 year or 500 hours, whichever comes first.  

Additional Features

  • Microphone Input
  • Automatic keystone correction
  • Wireless LAN (Optional)
  • USB Viewer
  • 6000 hour Filter Life
  • Auto power on
  • ECO Mode technology
  • Closed captioning
  • Variable audio out
  • Carbon savings meter
  • Virtual Remote
  • Sleep timer
  • Quick power-off
  • Built-in wall color correction
  • Advanced AccuBlend
  • AutoSense
Wireless Image Utility
  •  

    Optical

    Display Technology 0.59" LCD w/ MLA Light Output(Lumens) 3300 lumens
    Lamp Type 265W AC Light Source Life 3000 hours normal / 6000 hours eco
    Screen Size (diagonal) 58 to 110 in. / 1.47 to 2.79m Throw Ratio 0.36 to 1
    Projection Distance 1.47 to 2.8 ft. / 0.45 to 0.85m Projector Angle 49.2°
    Lens
    Zoom:
    1 to 1.4
    Focus:
    Manual
    F number, fnumber:
    F=1.8
    Keystone Correction Automatic or manual +/- 10°

    Mechanical

    Installation Orientation Floor/Front, Floor/Rear, Ceiling/Front, Ceiling/Rear Fan Noise 35 dB normal / 28 dB eco
    Regulations USA UL 60950-1 FCC Class B, C-UL CSA 60950-1 ICES-003 Class B  

    Built-In Closed Captioning
    Enables decoding and display of text information from a video.
    Variable Audio Out
    Adjusts the volume of an external speaker system using the projector's remote control.
    USB Viewer
    Permits playback (without a PC) of presentations or display images stored as JPG files from a USB flash drive.
    Virtual Remote
    Used over the VGA cable to control the projector directly from a computer without the need for additional control cables.
    AutoSense™
    Intuitively syncs the projector with most computer signals and features one-touch image optimization.
    ECO Mode™
    Extends lamp life, lowers audible noise and reduces total cost of ownership.
    Wireless LAN (Optional)
    Allows you to transmit images from a PC wirelessly to the projector, eliminating the need for traditional cumbersome cables.
    Crestron Roomview
    Provides unified management, including the ability to switch the power on and off for multiple projectors connected to a network.
    Quick Startup and Quick Power-Off
    Allows users to begin presenting within 3 to 4 seconds and allows immediate power off with no cooling required after shutdown to ensure efficient energy usage.
    eBeam Software
    Allows for annotation and collaboration on a whiteboard locally or via web meetings

    Awards

    NEC’s 3300-lumen interactive projector wins an Award of Excellence
    A judge panel of 30 educators select NEC’s collaborative projector bundle as the best solution in its industry.

    Warranty Length: 2 years.  Lamp warranty is 1 year or 500 hours, whichever comes first

    Large Screen Display Misc

    MultiPresenter Stick
    • Simple device PIN# access for secure connectivity
    • Screen mirroring for Android and Windows devices
    • Includes a simple annotation software allowing for user collaboration
    • Run apps and share files easily

    Multimedia Projector Misc

    Discontinued
    eBeam Interactive Stylus Pen
    Wireless LAN Module
    Refurbished
    Wireless LAN Module
    Refurbished
    Discontinued
    eBeam Interactive Stylus Pen

    Tools

    Discontinued
    NEC's Interactive Software (download)
    • Elevates control of your presentations and encourages interactivity between presenter and attendees
    • Interactive desktop builds on NEC’s original iPad-based interactive whiteboard software with the addition of audio/video screencasting. This feature allows teachers to easily capture their lesson presentations and share them with students before or after class. Class time can then be spent focusing on interacting and engaging with students rather than simply lecturing.
    • Control your Mac or PC wirelessly (remote keyboard and mouse) from anywhere in the room using your iPad
    • Quickly launch your documents and annotate over them in real time, including PowerPoint and Keynote slideshows
    • Create handwritten and drawn lessons on any background and save them for future playback
    • Control NEC projectors with the built-in Virtual Remote tool using the iPad touchscreen

      For orders of multiple licenses, please contact NEC
      at 866-771-0266
    Discontinued
    NEC's Interactive Software w/Stylus – Single License
    • Elevates control of your presentations and encourages interactivity between presenter and attendees
    • Includes interactive software for PC or Mac, stylus, USB flash drive with video tutorial and NEC Image Express software, license key and setup guide
    • Control your Mac or PC wirelessly (remote keyboard and mouse) from anywhere in the room using your iPad
    • Quickly launch your documents and annotate over them in real time, including PowerPoint and Keynote slideshows
    • Create handwritten and drawn lessons on any background and save them for future playback
    • Control NEC projectors with the built-in Virtual Remote tool using the iPad touchscreen

    Lamps

    Ultra Short Throw Replacement Lamp

    Mounts/Mounts Accessories

    Refurbished
    Discontinued
    Adjustable Extension Column, 12"–18"
    Refurbished
    Discontinued
    Adjustable Extension Column, 3'–5'
    Ceiling Plate
    Refurbished
    Ceiling Plate
    Adjustable Extension Column, 6" - 9"

    Cables/Adapters

    IR Receiver
    Power Cable
    Refurbished
    IR Receiver

    Replacement Remotes

    Remote Control
    Refurbished
    Remote Control

    Multimedia Projector Speakers

    Refurbished
    Discontinued
    Self-Powered Speaker

    • Remote control; Batteries
    • RGB cable
    • Power Cord, User's Manual
    • Product Registration Card
    • NP04WK wall mount
    • NP02Wi interactive module and pen

    Have a problem with your NEC Monitor? Here you'll find common questions. If you do not find a sufficient answer, please do not hesitate to contact us at 800-632-4662.

    Projectors

    • In the projectors on screen menu select the Setup option.
    • Under setup go to Installation or Installation 1 in the sub menu.
    • Within installation you will need to select Orientation.
    • In orientation select the box that says desktop front, press enter and change the option to either ceiling front or ceiling rear depending on which direction the unit is facing in regards to the screen.
    This tip works for most NEC Projectors: First, ensure that the projector is powered “on.” Second, hold down the “cancel” or “exit” button on the projector for about 15 to 20 seconds.
    • If the lamp indicator light on the projector is solid red then you would need to change the lamp as it has been used beyond its usable life.
    • Once the new lamp is installed you will need to reset the lamp hours of the projector with the remote control.
    • While the unit is in standby mode, meaning the power light is solid orange, you will need to hold down the help button on the remote for 10 to 15 seconds.
    • Once the lamp hours are reset the lamp LED light will go out and at that time the unit should power on normally.
    You will need an additional accessory called a remote mouse receiver -Part Number NP01MR. 3 Ways to Order:
    NEC projector input panels feature RGB computer inputs, a composite video input (yellow RCA type plug) and an S-Video input. The RGB computer input (blue) and can also be used with an optional component video adapter for connection to a DVD player or other video source, if desired.
    Function F* (this varies from computer to computer)
    This can be done by going into the OSM and making the change there or by sending a specific RS232 command to the projector from a computer.
    If you are experiencing an issues related to image quality, colors, and signal, Factory Reset is the first setup to perform. (Please make a note of any custom setting prior to doing a factory reset.)
    With certain NEC projectors it is possible to project onto non-flat surfaces such as cylinders or corners using free software such as the Geometric Correction Tool, Keep in mind that the 16:9 format will not be supported.

    To permanently save your digital keystone corrections by activating "3D Reform Memory." To do this:

    1. Go to the "Extended Menu" and choose "Projector Options."
    2. Choose "Setup" and go to page 4.
    3. Choose the checkbox "3D Reform Memory" and press OK.

    Your horizontal, vertical and diagonal 3D reform (keystone) data will now be permanently saved.

    The flash memory card or USB drive must be formatted with the FAT16 or FAT file system. (FAT32 and NTFS are not recognized.)
    The PC card slot, which is situated on the projector main unit, allows you to make presentations without a PC. Just insert a compact flash or flash memory card containing your stored presentation material and display images directly onto a screen. The projector will display JPEG, BMP, TXT and text-only HTML files.

    To present your digital images or stills using an NEC projector you can use the following memory cards:

    Compact flash cards (with a Type II PCMCIA CF adapter)
    Smart media (with a 4-in-1 Type II adapter)
    Memory stick (with a 4-in-1 Type II adapter)
    Memory stick pro (with a 4-in-1 Type II adapter)
    Multimedia card (with a 4-in-1 Type II adapter)
    Secure digital (with a 4-in-1 Type II adapter)

    The PC Card Viewer and the Blackboard Function. Projectors equipped with the PC Card Viewer feature are particularly suitable for mobile use since you do not need a notebook or PC to make a presentation. Instead, you can take your presentation along with you stored on a normal PC card or Compact Flash card. Meanwhile, the Blackboard feature allows you to create drawings via the USB mouse and project them onto a screen, facilitating interactive presentations and audience rapport.
    Yes. NEC projectors are fitted with inputs for video and S-Video, and meet NTSC, PAL, SECAM, 4.43NTSC and PAL60 standards. You can connect the projector using video, S-video and component (YUV) cables. Please, all projectors are PAL Progressive-enabled (via YUV or RGB). The latest NEC projectors produce virtually no irritating fan noise.
    Most projectors use LCD technology. This splits light into the primary colors red, green and blue. Each color is then directed through an LCD display acting as a ‘light valve’ and the light is then reassembled. There is an LCD display for each individual pixel and each primary color. DLP technology involves the use of huge numbers of tiny quadratic mirrors arrayed on a Texas Instruments DMD chip. Only when a mirror is tilted will it reflect the light shining onto it back towards the screen. This very high-frequency switching on and off of points of light is not perceived by the human eye and allows different shades of color to be portrayed. The colors are generated by a color ribbon featuring the primary colors red, green and blue.
    It depends on the installation environment. In environments with more ambient light, we recommend choosing DLP. For the greatest flexibility, choose an NEC projector that features both technologies.
    Check your projector's installation guide, or use our Image Calculator.

    Keep in mind that distances shown in the Installation Guide or Image Calculator may vary ± 5%. We recommend that you verify the distance before the projector is installed.
    As a general rule, the distance between the viewers and the screen should between 1.5 and 6 times the image width.
    Your ideal screen will depend on your installation, the size of the room, the amount of ambient light, and other factors. We recommend contacting your installer or a screen vendor for screen recommendations.
    Most lamps have an expected life of about 2000 hours.

    There are several things you can do to increase your lamp life.

    • Always make sure there is adequate clearance near the intake and exhaust vents.
    • Keep the environment clean and relatively dust free.
    • Clean air filters every 100 hours, or more often if there are a lot of dust or contaminants in the room.
    • Striking the lamp ages the lamp as it causes slight changes to the shape of the electrodes that light the lamp, so light up your projector when you're ready to use it and avoid frequent on and off cycles.
    • Avoid shock to the lamp or projector. • Use Eco-Mode, if your projector has it. • After you run the projector, leave it plugged in until the fan turns itself off. • Avoid storing the lamp or projector in extreme temperatures or humidity levels.

    Certain projector lamps contain mercury. Some states have laws that require projector lamps to be disposed of as a hazardous material if they contain mercury. Check with your audio-visual sales associate or local municipality to find out what the projector lamp disposal laws are for your state. You may also contact NEC Technical Support to have your lamp recycled by NEC Display Solutions.

    For Windows XP (ver. 2.08):

    LT265 & LT245 (Firmware Version: 1.04 or later) / WT610 (Firmware Version: 1.08 or later) / LT380 / LT280 / NP3150 / NP2150 / NP1150 / NP3151W / NP905 / NP901W / NP2000 / NP1000 / VT800

    For Windows Vista (ver. 2.08):

    LT265 / 245 (Firmware Version: 1.04 or later) / WT615 / 610 (Firmware Version: 1.08 or later) / LT380 / 280 / NP3150 / NP2150 / NP1150 / NP3151W / NP905 / NP901W / NP2000 / NP1000 / VT800

    For Mac OS (Intel) (ver. 1.2.5)

    LT265 / LT245 (Firmware version: 1.03 or later) / LT380 / LT280 / NP3150 / NP2150 / NP1150 / NP3151W / NP905 / NP901W NP2000 / NP1000 / VT800* / WT610 (Firmware version: 1.00 or later)

    For Mac OS (PowerPC) (ver. 1.2.4)

    LT265 / LT245 (Firmware version: 1.03 or later) / LT380 / LT280 / NP3150 / NP2150 / NP1150 / NP3151W / NP905 / NP901W / NP2000 / NP1000 / VT800* / WT610 (Firmware version: 1.00 or later)

    *The "Easy Connection" function cannot be used with VT800.

    Virtual Remote Tool is compatible with NP300/400/500/500W/600 models.
    PC Control is designed to control a single projector, while PC Control Pro is designed to control multiple projectors.
    The PC Control Utility or PC Control Pro can be connected from your computer to the projector using a serial or LAN connection.
    Select "Lamp Mode" on the remote control and use the menu to select Eco-Mode.
    Excessive moisture, dust, heat and smoke.
    You're seeing the result of dust build-up on the green LCD panel. We recommend that you schedule a service visit. Please contact NEC technical support or your local NEC service provider to set it up.
    No, NEC only provides service support and parts to NEC authorized servicers and technicians. NEC-authorized service centers/technicians have attended training classes to ensure quality service on NEC products
    Contact Sales Contact Support